Redcliffe & Moreton Bay Area – Same-Day Service

Burst Pipe Repairs

DR Smith Plumbing and Roofing is based in Clontarf and works across the Redcliffe and Moreton Bay area.

15050088
QBCC licence
Redcliffe
On the peninsula
Burst Pipe Repairs
When a water pipe bursts
When a water pipe bursts

A burst pipe is a split or broken water supply line, and until the water is turned off it keeps leaking at full mains pressure. Fixing it means finding the break, cutting out the damaged length and joining in new pipe. The size of the job depends on where the pipe runs, whether that’s in the open, inside a wall, beneath the slab or buried in the yard.

Burst pipe repairs: key facts

  • Repairing a broken or damaged pipe is minor work: it must be done by a QBCC licensee, but it isn’t approved by council or reported afterwards.
  • Replacing or altering supply pipes at an existing building is a different category, notifiable work, which we register with the QBCC on a Form 4.
  • You can temporarily turn off the stop tap at the water meter to stop a leak wasting water, provided you first check it won’t damage an appliance such as the hot water system.
  • The meter test is to photograph the meter numbers, including the red ones, use no water for at least an hour, then check whether they’ve changed.
  • Pressure limiting devices protect the pipes inside a property from swings in high pressure, and a house built after two thousand and six most likely has one.
  • A house built before nineteen sixty is highly likely to have galvanised water pipe.

How a burst shows up

  • Water spraying or pouring from a pipe you can see.
  • The pressure drops suddenly, or the taps give nothing at all.
  • You can hear water running when nothing in the house is turned on.
  • A wet patch spreads across a ceiling, a wall or the floor.
  • Part of the yard goes soggy, or water bubbles up along the line of a buried pipe.
  • The water meter keeps moving with every tap off.

Why pipes burst

A supply pipe is under pressure all day and night, so any weak point eventually gives. Causes include these.

  • High pressure, or the shock when a tap or an appliance valve snaps shut, which is called water hammer.
  • Corrosion, at a fitting or along an old metal pipe.
  • A poorly made joint that has worked loose over the years.
  • Ground movement and tree roots pressing on a buried pipe.

The broken section usually shows us which it was. A clean split points to pressure or a knock. Pitting and rust inside the wall of the pipe point to corrosion, which matters because the rest of that run has aged the same way.

Clamp, cut-out repair or a new run

Repair What it is When it suits How the law treats it
Repair clamp or coupling A sleeve or fitting sealed over the break to get water back on A pipe that’s hard to reach, while the permanent fix is planned Minor work under the QBCC’s categories: repairing a broken or damaged pipe
Cut-out repair The damaged length cut back to sound pipe and new pipe joined in One break in a pipe that is otherwise in good condition Also minor work: a licensee does it, but nothing is lodged
Replace the run A new pipe laid from one point to another, often the meter to the house Corroded or galvanised pipe that has burst before, or a main line under a slab Notifiable work: registered on a Form 4

Finding and fixing the break

With the water off, we open a low tap to drain the line. If the break is out of sight, we trace the run of the pipe to the wettest spot. Then the opening only needs to be big enough to reach it. That might be a square cut from the plasterboard, a lifted floorboard or a short trench in the yard.

We cut the pipe back to sound material on both sides of the split. A new length goes in with fittings to suit the copper or poly that’s already there. Then we bring the water back on slowly, check every new joint for weeping, and run the taps until the air has cleared from the line.

Sometimes the permanent repair can’t happen straight away, because the pipe is under the slab or the whole run needs replacing. In that case a repair clamp or a coupling can get the water back on, and the full fix is a separate job.

An exposed pipe under the house or in a cupboard is the quickest kind of burst to repair. The job grows when the pipe is buried in a wall or a slab, or when it’s the main line from the meter to the house. It grows again when the old pipe is corroded enough that more leaks are likely to follow. If high water pressure caused the burst, a new length of pipe leaves that cause in place, so we check the pressure too. Drying out carpet and patching walls is a separate job from the pipe repair.

Storms, old pipe and pressure on the peninsula

October to April is the peak season for severe storms and flooding. Storms bring soaked ground and fallen trees, and both can put a buried pipe under strain. Older homes carry a second risk. Galvanised pipe is highly likely in a house built before nineteen sixty, and it should be checked for corrosion, which we do when we open up the line. Pressure is the third factor. Limiting devices protect household pipes from swings in high pressure, and we check that a new home’s device is set correctly.

What to know before we arrive

Under Queensland’s plumbing rules, the burst pipe itself is work for a licensed plumber or drainer, which is what we are. Repairing a broken or damaged pipe is minor work: still licensed work, but nothing is lodged.

What you can safely do while you wait for us is stop the water and keep away from anything electrical it has reached. The full first steps are on the emergency plumbing page. In short, close the stop tap at the meter, and if it won’t move, don’t force it.

Then open the lowest tap in the house to let the pipes drain, and take photos of the damage before you mop up.

If you only suspect a burst, because the pressure has dropped or part of the yard is soggy, check the meter before you shut anything off. Turn every tap off and photograph the numbers. If the dial is moving with nothing running, water is escaping somewhere past the meter, and we find it.

When you ring, have ready where the water is showing, whether the stop tap closed, and roughly how old the house is. If you can see the pipe, tell us whether it’s copper, plastic or grey galvanised steel. Mention any earlier bursts, and whether water has reached the power.

A cut-out repair or a clamp leaves nothing lodged, and we leave every joint dry with the water back on at full pressure. A replaced run is notifiable, so we lodge the Form 4 and the owner, or whoever engaged us, gets a copy. A licensed plumber may only install listed plumbing products that carry the WaterMark, and that is what we fit.

That returns the page to the rule it began with: the stop tap is yours to turn, and under Queensland’s rules the pipe repair is work for a licensed plumber.

Burst pipes, leaks and pipe replacement

A burst is water you can see or hear escaping fast. Leak detection and repair is for slower losses you can’t find, such as a meter that creeps with everything off. Water pipe replacement renews whole runs of old or corroded pipe, rather than fixing one break. Water pressure testing checks whether high pressure is what’s straining the pipes.

If a pipe has burst at your place, call DR Smith Plumbing and Roofing on 0483 965 800. We’re based in Clontarf and repair water pipes from Redcliffe through the Moreton Bay area.

Burst Pipe Repairs
Call 0483 965 800Request a quote
QBCC 15050088

Common questions

Call if your question is not covered here.

Not for a repair. Repairing a broken or damaged pipe is minor work, so nothing is registered, although a QBCC licensee still has to do it. If the old run is replaced instead, replacing supply pipe at an existing building is notifiable work. We then register it on a Form 4 and give you a copy.

Start with the pressure. Limiting devices protect the pipes inside a property from swings in high pressure, and a house built after two thousand and six most likely has one. If pressure is a concern, we fit one at the meter. If the pipe itself is old and corroded, it may be time to replace the worst runs.

Only if the burst is on a branch you can close off with its own valve, such as the pipe to a single basin. Close that valve and the rest of the house can have water again. If the burst is on the main line, the water stays off until the pipe is repaired or clamped.

Not automatically. We inspect the pipe around the break, and if it is sound, a cut-out repair is enough. If it’s corroded or galvanised, and especially if it has burst before, the rest of that run has aged the same way. Then replacing the worst runs can make more sense, even though it is a bigger job with more paperwork.

Turn the water off and leave the pipe to us. A home patch on a mains-pressure pipe can let go once the water is back on, and then you’re mopping up twice. Repairing a broken pipe is licensed work, so keep the stop tap closed and the pipe as it is.

Where we work

DR Smith Plumbing and Roofing is based in Clontarf on the Redcliffe peninsula and works across the Moreton Bay area. For Burst Pipe Repairs in Clontarf or one of the suburbs below, call 0483 965 800. The same number covers plumbing and roofing jobs.

Map of our Clontarf base. Opens Google Maps

Click map view in Google maps

Roofing services

Steel roof repairs, re-roofing and gutters from the team you already call for plumbing, based in Clontarf.

See all roofing services

SPEAK TO US TODAY!

We look after both your plumbing and your roofing, so there is one number to call for either job: 0483 965 800.