Redcliffe & Moreton Bay Area – Same-Day Service

Tap Repairs and Replacement

DR Smith Plumbing and Roofing is based in Clontarf and works across the Redcliffe and Moreton Bay area.

15050088
QBCC licence
Redcliffe
On the peninsula
Tap Repairs and Replacement
Where taps wear out
Where taps wear out

A dripping or leaking tap usually needs a new washer or cartridge, fresh O-rings, or the worn seat inside it ground flat again. When the body of the tap is corroded or cracked, or you can’t get parts for it any more, a new tap is usually the better job. Which of those yours needs becomes clear once it’s apart.

Tap repairs and replacement: key facts

  • Replacing a jumper valve or washer in a tap is unregulated work, which needs no licence, approval or notice.
  • Replacing the tap itself is different: that work must be done by an appropriately licensed person, and we are licensed plumbers.
  • Replacing a tap counts as minor work, so nothing is lodged with the council or the QBCC afterwards.
  • On the national water rating label, three stars means more than seven and a half and up to nine litres a minute, the building code minimum for taps.
  • The water rating scheme suggests five or six star taps for a bathroom basin, and three or four star in the kitchen and laundry so pots and tubs still fill.
  • When only particular taps run weakly, the problem is in the house plumbing, and the tap’s own filter is the first place we look.

What a worn tap does

  • It keeps dripping from the spout after you’ve turned it off firmly.
  • Water weeps around the base, or creeps up past the handle when the tap is running.
  • The handle is stiff, squeals as you turn it, or needs more and more force to stop the flow.
  • The pipes bang when you shut the tap quickly.

Washer taps and mixer cartridges

There are two kinds of tap in most homes, and they wear out differently. An older tap takes several turns to close, and inside it a rubber washer on a jumper valve presses down onto a brass seat. Each close squashes the washer a little, and over time it hardens or splits. The seat can also pit or score, and then water gets past even a new washer.

A lever mixer, and most taps that close in a quarter turn, use a ceramic cartridge instead. Two discs slide over each other to open and close the flow. When the discs wear or grit scores them, the tap drips from the spout, and the fix is a new cartridge rather than a washer.

Washer tap Ceramic cartridge or mixer
How it closes Several turns of the handle A quarter turn, or a lever
What wears The washer on the jumper valve, and the seat under it The ceramic discs, and the O-rings around the cartridge
Usual repair New jumper valve, with the seat ground smooth or replaced New cartridge for a spout drip, new O-rings for a handle or base leak
When a new tap wins The body is corroded or the seat is too far gone The cartridge can’t be matched, which happens with old or unusual mixers

Fixing it or swapping it

First we turn the water off, at the small isolation valve under the basin or sink if there is one, and at the meter if there isn’t. Then we open the tap so the line drains and nothing sprays when it comes apart.

On an older tap, the headgear, the screw-in body under the handle, comes out, and with it the jumper valve that carries the washer. A new jumper valve goes in. We then check the seat it closes onto and grind it smooth or replace it before the headgear goes back.

When the tap has to go, we disconnect the flexible hoses underneath and undo the nut that clamps the tap to the basin or bench. The new tap goes in with fresh seals and the hoses are reconnected. We run it with the aerator off to flush out grit the work has stirred up, then the aerator goes back on.

A washer change on a basin tap that’s easy to reach is quick work. The job grows when the isolation valves under the basin have seized and need replacing as well, or when the stop tap at the meter won’t close. Taps set into a wall, as many shower and bath taps are, take longer to get at. So does a benchtop that’s chipped or cracked around the old tap hole, because the new tap needs a sound surface to seal against.

Older homes add one more factor. Houses built before nineteen sixty are linked with galvanised pipe in Unitywater’s area, and corroded pipe behind a tap can turn a simple swap into a longer job.

What to know before we arrive

Queensland draws a clear line through this job. Replacing a jumper valve or washer in a tap is unregulated, while replacing the tap itself must be done by an appropriately licensed person. Replacing a kitchen, basin or shower tap is minor work, with no form.

Find your shut-off points now, so you can stop a tap that won’t close properly while you wait for us. Look under the basin or sink for an isolation valve on each pipe. If there’s none, use the stop tap at the meter, which sits on the road side and closes clockwise. If it won’t turn, don’t lean on it, because a broken stop tap makes the job bigger. Ring us and we free it.

Watch where the water comes from before you ring. A drip from the spout once the tap is shut points to the washer, the cartridge or the seat. Water around the base, or creeping past the handle, is usually an O-ring. For a weak tap, turn on the other taps in the house and compare. If only one runs poorly, the problem is in the house plumbing, and we start with that tap’s filter.

The tap itself is ours to deal with, washer and all. The headgear and the nut under the basin can both be seized, and forcing either in a cramped cupboard can crack a basin or kink a hose.

When you ring, tell us which tap, whether it’s hot or cold, and whether it’s a turning tap or a lever. A photo of the tap and any maker’s name on it helps identify the right parts. A tap that won’t shut off at all needs the water isolated and a call. A drip is a worn washer or cartridge, and a booked visit stops it before it wastes more water.

A replaced tap is minor work, so there’s no Form 4. It carries the WaterMark, because a licensed plumber isn’t permitted to fit a listed product type without it. The new tap has a water rating label as well.

That brings the law full circle: the washer inside is on the unregulated list, and the tap itself is work for a licensed plumber.

Taps, fixtures and kitchen plumbing

This page is about fixing or swapping a tap. Bathroom fixture installation covers new basins, showers and tapware as a set, often in a new layout. Kitchen plumbing takes in the sink, the dishwasher connection and the waste as well as the mixer. Water pressure testing is the answer when taps bang or every tap in the house is weak.

If a tap at your place won’t stop dripping, ring DR Smith Plumbing and Roofing on 0483 965 800. Working from Clontarf, we fix taps in Redcliffe kitchens and bathrooms, and further afield across the Moreton Bay area.

Tap Repairs and Replacement
Call 0483 965 800Request a quote
QBCC 15050088

Common questions

Call if your question is not covered here.

Fix it if the body is sound and parts are still around. Replace it when the body is corroded, the seat is too far gone to grind back, or nobody makes the cartridge any more. Which way makes sense is clear once the tap is apart and we can see the seat or cartridge.

No. A lever mixer has a ceramic cartridge where an older tap has a washer. A drip from the spout usually means the cartridge is worn, and the fix is a new one. A leak around the handle or base can often be fixed with new O-rings. If an old or unusual mixer’s cartridge can’t be matched, a new tap is usually the better fix.

That bang is water hammer. Water moving through the pipe stops dead when a tap shuts fast, and the shock runs back along the line. In Unitywater’s area, a house built after two thousand and six most likely has a pressure limiting device, generally in the meter box or on the hot water inlet. We can check whether yours has one and whether it is working.

For a bathroom basin, the national water rating scheme suggests five or six stars, which can cut water use by half or more compared with three stars. In the kitchen and laundry it suggests three or four stars, so the tap still fills a pot or a tub quickly. Bath spouts don’t need a rating, because they have to fill fast.

It may be meant to. A Queensland Government guideline requires a temperature control device when a hot water system is installed or replaced, holding showers, baths and basins to fifty degrees. Kitchen and laundry taps aren’t covered, so they can run hotter. If a bathroom tap runs scalding, ring us. Fitting a device is notifiable work, and we lodge the Form 4.

Where we work

DR Smith Plumbing and Roofing is based in Clontarf on the Redcliffe peninsula and works across the Moreton Bay area. For Tap Repairs and Replacement in Clontarf or one of the suburbs below, call 0483 965 800. The same number covers plumbing and roofing jobs.

Map of our Clontarf base. Opens Google Maps

Click map view in Google maps

Roofing services

Steel roof repairs, re-roofing and gutters from the team you already call for plumbing, based in Clontarf.

See all roofing services

SPEAK TO US TODAY!

We look after both your plumbing and your roofing, so there is one number to call for either job: 0483 965 800.